Welcome To Your New Home At 101 Grand

This Tech Guide for 101 Grand Ave provides a simple reference for setting up and using the essential systems and smart features in your home

Light Switches

Once you have wifi installed in your new home you will be able to pair light switches to the iotty app.

Your home is equipped with Iotty smart light switches. To control them from the iotty app follow these steps. The app will also allow you to control the backlight. 

Before you start note which lights are controlled by more than one light switch, this will be important when registering all lights. Also be mindful to name each light with a unique name. This will be helpful in daily use of the app.

Step 1: Download the App

Download and open the “Iotty” app.

Step 2: Create or Log In to Account

Tip: Don’t skip verification — pairing won’t complete without it.

Step 3: Confirm Wi-Fi Requirements

Before pairing:

• Your phone must be connected to 2.4 GHz Wi-Fi.
• If you have a dual-band router, temporarily disable 5 GHz or move further from router to force 2.4 GHz.

Step 4: Remove Front Plate from Switch

• Grip the top and bottom of the plate with both hands.
• Pull from the bottom, and plate will snap off.

Step 5: Prepare Device for New Pairing

• When pairing a new device using a paperclip or pin press the AP button once.
• This removes the device from any previous pairings.

Step 6: Add Single Switch in the App

1. Open the app.
2. Tap the + (Add Device) button.
3. Select: Connect device to Wi-Fi.
4. App will start searching for devices.
5. The app will pull a list of devices available nearby: you will need to match the serial number from the switch to the app.
6. Once you have found the correct device number click on it.
7. The app will prompt you to enter the wifi password. Enter password and press connect.
8. The app will then register the device.
9. Once registration is successful app will prompt you to start configuration.
10. Click Start Device Configuration.

Device Configuration

• If switch is a one way all you need to do is label the switch.
• Lights that are controlled by only one switch should be set as “On/Off Switch”.
• If switch has a dimmer that will automatically be registered.
• If the switch has multiple lights it controls then the app will have you label each light. You are able to manually turn lights on and off when the plate is removed so that you know which lights you are labeling.
• Press Next.
• The next screen will allow you to name the plate. Enter a plate name and press Next.
• The final step is to press Save.

Registration Complete

• You have successfully registered this switch.
• You will need to do this for each switch in your new home.
• You can now return the switch cover, it pops back into place.

When Pairing a Light That Can Be Controlled by Multiple Switches

1. Follow steps to pair the first light switch.
2. When you go to pair the second light switch you will take additional steps.
3. Follow steps 1–10.
4. When you get to device configuration on a switch that you know pairs with another switch you will take additional steps.
5. On the app for this switch you will select “Multiway (3/4 Way)”.
6. The app will prompt you to select from which plate and switch you want to pair the current switch with.
7. From here you can continue from step 10.

Helpful videos - Iotty Setup Playlist 

Forced Air Thermostat

Your home is equipped with a Mysa smart thermostat. To control the thermostat from the Mysa app follow these steps.

Before you start, make sure:

• Your thermostat is powered on.
• Bluetooth is enabled on your phone.
• Your phone is connected to a 2.4 GHz Wi-Fi network (Mysa does not support 5 GHz-only networks).
• You have the Mysa app installed.

Step 1: Put Mysa in Pairing Mode

• If the pairing icon is not showing on the thermostat:
• Press and hold the up and down arrows simultaneously for about 10 seconds.
• Wait for the pairing symbol (Bluetooth or Wi-Fi icon, depending on the model) to appear.

Step 2: Open the Mysa App

1. Open the Mysa app and sign in.
2. Tap Add Mysa or Add Thermostat.
3. Select your thermostat model.

Step 3: Connect to the Thermostat

1. Stand within a few feet of the thermostat.
2. Allow Bluetooth permissions when prompted.
3. Select your thermostat from the list.
4. Tap Identify if prompted to confirm it's the correct device.

Step 4: Connect to Wi-Fi

1. Choose your home's 2.4 GHz Wi-Fi network.
2. Enter your Wi-Fi password.
3. Wait for the thermostat to connect.

Step 5: Finish Setup

1. Name the thermostat (e.g., Living Room, Bedroom).
2. Assign it to a room.
3. Allow any firmware updates to complete before closing the app.
   

Refrigerator

The refrigerator will be on and running prior to move-in.

Temperature controls are located inside the refrigerator at the top of the unit.

The freezer's ice maker is turned off by default. If you would like to use the ice maker

Tip: It is normal to hear the refrigerator cycling on and off periodically. This is part of the appliance's high-efficiency operation.

Care Tips

• Avoid blocking interior air vents with food items to allow proper airflow.

• After loading groceries, the refrigerator may take some time to return to its normal temperature.

• Wipe interior shelves with a damp cloth as needed.

• Clean door seals periodically to help maintain an effective seal.

Windows

A one-time exterior window cleaning has been completed prior to move-in. Future exterior window cleaning is not provided.

Operable Windows

Windows can either swing open or tilt inward for ventilation.

Always ensure windows are fully closed and locked before leaving the unit, especially during windy or coastal weather conditions.

If a window feels stiff, do not force it. Salt air can occasionally affect window operation. Please submit a maintenance request if assistance is needed.